Loading


Fanotec Pole Series

Tripod Adapter (Type B) for Pole Series 1 and Series 2



Tripod Adapter for Use with Fanotec Poles

This adapter allows using a rigid tripod to support Fanotec Poles Series 1 and 2. It spreads the bending torque to a long distance of tripod center column and pole, thereby reducing the risk of damaging the tripod top plate, the rotator or the pole base.
The tripod adapter with a rigid tripod will greatly stabilize the pole, making it ideal for long exposure and HDR photography. Users will have greater reassurance against wavering pole when shooting around crowds or in windy situations.
An optional guy wire system can be used to further stabilize the pole for heavy loading, or in strong winds or when very long exposure is needed.
Note that the bending torque can be greatly amplified when using a long pole. Use only a rigid tripod with tripod adapter to support a Fanotec pole.
EXHIBIT CAUTION WHEN USING POLES AROUND PEOPLE AND ELECTRICAL WIRES.


Package Contents of Tripod Adapter (Type B)


Package Contents of Tripod Adapter Type B
Spare Parts Qty
4mm hex key 1
Center column fitting 1


Prerequisites of using Tripod Adapter (Type B)


Prerequisites of using Tripod Adapter Type A
  • Tripod with a center column diameter of 25mm, 26mm, 28mm or 32mm.
  • Tripod must have a shoulder plate radius less than 54mm / 2.1".
  • A Fanotec rotator or a 3/8" to M6 internal thread reducer must be used.

Top .:. Bottom


Installing Tripod Adapter to Tripod Center Column


Installing Tripod Adapter to Tripod Center Column
Remove any accessories from center column that (being bigger) blocks the attachment of lower adapter. Some parts can be stowed at the bottom of the lower adapter.
Set up tripod at its shortest extension.

Installing Tripod Adapter to Tripod Center Column
Install the appropriate fitting to the lower adapter as needed. Loosen the side knob of lower adapter. Keep the flange of fitting facing down. Insert the fitting from the bottom of the adapter.

Installing Tripod Adapter to Tripod Center Column
With side knob loosened, insert the lower adapter to the center column. Place it at 5cm (2") from the end of center column. Adjust its position so that it is evenly spaced from 2 tripod legs. Tighten its side knob fully. Press it to test it is securely fastened.

Installing Tripod Adapter to Tripod Center Column
Align and place a Fanotec rotator on the adapter. Tighten the rotator by either using 2 M5 screws or the M6 screw knob. When a motorized rotator is used atop a pole, the pole can be mounted directly to the adapter. Skip this step and go to Step 4A.

Installing Tripod Adapter to Tripod Center Column
To use a Pole 1 or a Pole 2 upper unit on the adapter, the Pole 2 to Pole 1 Fitting must be installed. To use a Pole 2 lower / complete unit on the adapter, the fitting (if any) must be removed. See Step 5A & B for instructions on installing / removing the fitting.

Installing Tripod Adapter to Tripod Center Column
Install the upper tripod adapter on top of tripod center column. Tighten its top knob very gently so that it can be twisted freely to align with the lower adapter.

Installing Tripod Adapter to Tripod Center Column
Install a 3/8" x 3/4" stud (from the pole package) at the base of pole using the included hex key, except when a Pole Rotator is mounted on the lower adapter, or when a motorized rotator is to be used atop a pole. Tighten the stud fully to prevent loosening.

Installing Tripod Adapter to Tripod Center Column
Loosen the handle at the side. Insert the pole into the upper adapter. For Pole 1 and Pole 2 upper unit, the base cap must be first removed, then reinstalled after inserted the pole into the adapter.

Installing Tripod Adapter to Tripod Center Column
Slowly lower the pole while holding the base with one hand. Twist the upper adapter to align for the 3/8" thread on the rotator. Then carefully tighten the pole to the rotator. When a motorized rotator is used, skip this step and go to Step 9A.

Installing Tripod Adapter to Tripod Center Column
Tighten the knob at the side of upper adapter. This will align the upper and lower adapters. Hold the upper adapter and slowly tighten the top mounting knob to prevent twisting. Use the upper adapter as pivot to fully tighten the knob.

Installing Tripod Adapter to Tripod Center Column
Mount the pano head and camera with remote control atop the pole.
Carefully extend the tripod legs to 50-80% extension, depending on how much rigidity is needed.
Level the pole by adjusting the tripod legs. Carefully raise up the pole.
When everything is done, loosen the side knob slightly so that the pole can be rotated smoothly with just enough friction to stabilize the pole.
NEVER LEAVE POLE UNATTENDED. UNEVEN SURFACES OR WINDS MAY CAUSE LEANING AND/OR FALLING OF EQUIPMENT!

Top .:. Bottom


Step 4A: Using a Motorized Rotator with Tripod Adapter


Using a Motorized Rotator with Tripod Adapter
Install an optional 3/8" to M6 internal thread reducer to the base of pole using a screw driver or a coin. Tighten it fully to prevent loosening. Remove the rubber O-rings at the base of pole. Then continue to Step 5.


Step 5A & B: Installing and Removing Pole 2 to Pole 1 Fitting


Installing and Removing Pole 2 to Pole 1 Fitting
To use Pole 1 or Pole 2 upper unit on tripod adapter, the fitting must be installed. Loosen the side knob. With the flange facing up, squeeze and push the fitting into the adapter. The fitting should snap in place. Then continue to Step 6.

Installing and Removing Pole 2 to Pole 1 Fitting
To use Pole 2 lower unit on tripod adapter, the fitting (if any) must be removed. Loosen the side knob. With the flange facing down, squeeze and push the fitting out of the adapter. Then continue to Step 6.


Step 9A: Using a Motorized Rotator with Tripod Adapter


Using a Motorized Rotator with Tripod Adapter
Slowly lower the pole while holding the base with one hand. Twist the upper adapter and rotate the pole to align for the anti-twisting pins on the lower adapter. Then tighten the pole to the adapter using the central M6 screw knob. Then continue to Step 10.


Removing Unused Screws from Tripod Adapter


Removing Unused Screws from Tripod Adapter
The screws are made captive by using rubber O-rings. If only one type of screw will be used, the unused one(s) can be removed. Simply pull the M6 screw knob downward to remove it. Use a hex key to push the M5 screw up. Use a toothpick or similar to remove the O-ring. Then the screw will come off with hex key.

Nodal Ninja Quick Reference Guides



Accessories
Nodal Ninja Anti-Twisting Camera Mounting Plate
fr - Plaque d'attache rapide anti-rotation Nodal Ninja + video tutorial
Camera Plates with Anti-twisting Flange
Camera Plate C2
Specification for Fanotec Arca Style Camera Plates
Quick Release System Mounting Instructions
fr - Manuel de la plaque de montage rapide QRS2
Nadir Adapter for NN3, NN4 and NN5
EZ-Leveler II + video tutorial
Rotator Foot Plate for Poles
Replacing Upper Rotator Knob For Nodal Ninja Ultimate M1
fr - Remplacement de la molette supérieure de la rotule Nodal Ninja Ultimate M1

Advanced Rotators
Nodal Ninja - RD8 + video tutorial
Nodal Ninja - RD16 + video tutorial
Nodal Ninja - RD3L + video tutorial
Rotator Mini

Discontinued
Nodal Ninja SPH-2
Nodal Ninja SPH-1

Fanotec Pole Series
Using Pole Series 1 and the Extension Unit
Using Pole Series 2 Upper and Lower Unit
Tripod Adapter (Type A) for Pole Series 1 and Series 2
Tripod Adapter (Type B) for Pole Series 1 and Series 2

Lens Ring Mounts
Lens Ring Component Build Chart

M1 Ultimate Series
Nodal Ninja Ultimate M1
Nodal Ninja Ultimate M1 - L/S
M1-S Ultimate Series
Nadir Adapter on M1L
fr - Guide d'installation de l'Adapteur Nadir pour Ultimate Modular M1-L

M2 Ultimate Series
Nodal Ninja Ultimate M2 Gimbal Pano Head With Rotator D8II or D16II

NN 180
Nodal Ninja 180 w/RD4 + video tutorial

NN3 Series
Nodal Ninja 3 MKII
Nodal Ninja 3 MKII w/RD3L + video tutorial
Nodal Ninja 3 MKII w/RD8 + video tutorial
Nodal Ninja 3 MKII w/RD12
Nodal Ninja 3 MKII w/RD16 + video tutorial

NN4 Series
Nodal Ninja 4
Nodal Ninja 4 w/RD8
Nodal Ninja 4 w/RD16 + video tutorial

NN5 Series
Nodal Ninja 5 + 5L
Nodal Ninja 5 w/RD8 + video tutorial
Nodal Ninja 5 w/RD12
Nodal Ninja 5 w/RD16 + video tutorial

R1/R10
Nodal Ninja Ultimate R1 - Ring Mount Pano Head
fr - Nodal Ninja Ultimate R1 - Tête pano avec anneau
GTP with R10 (Google Trusted Photographers)
GTP R10 Package for Sigma 8mm f/3.5 for Canon
GTP R10 Package for Sigma 8mm f/3.5 for Nikon
GTP R10 Package for Canon EF 8-15mm
Lens Ring for Sigma 8mm Fisheye Canon Mount
Lens Ring for Sigma 8mm Fisheye Nikon Mount
Lens Ring for Canon EF 8-15mm f/4 L USM
R1 NPP for Sigma 8mm F3.5 Canon and Nikon
R10 NPP for Sigma 8mm F3.5 Canon and Nikon

Only buy from authorized resellers. If buying new from other than an authorized reseller, no warranties or product support are included.

topTop

Line

Nodal Ninja


Exclusive distributors of the Fanotec product line. Fanotec develops and manufactures exclusively products to meet the needs of the panoramic photographer. We offer products such as the award winning Nodal Ninja, the CNC machined Ultimate Line, Carbon Fiber Aerial Poles, Levelers, and many more related accessories. Many of these items may also be used for general photography as well.

Resellers


Check for a reseller in your country.
Resellers

News

Line
Line
NN3 MKII NN4 M1 R1 Poles EZ-Leveler II

Line
STORE    SITEMAP    FORUM
Testimonials | Trade In's | User Guides | Find a Reseller | Affiliates | Terms of Use | Your Account | Contact
Accredited Business Bureau   D-U-N-S Registered   LinkedIn   youtube   twitter   flickr   facebook   
Nodal Ninja®, 3454 N. San Marcos Pl. Ste 9, Chandler, Arizona, 85225 USA Customer Service ph: 480-659-9899 / fax: 480-452-0452 Hours: M-T-TH-F 8am-12pm
© 2013 Nodal Ninja® | Nodal Ninja® is a Registered Trademark - All Rights Reserved.

Verified Merchant   PayPal Verified