Loading

13. Finding the Entrance Pupil of a Lens

Fanotec® Spherical Panoramic Tripod Head Nodal Ninja 5 & 5L - Complete Manual

What is the Nodal Point or Entrance Pupil and why is it important?

We would like to take a moment and dispel misconceptions of the word "Nodal Point". When referring to this no parallax point (NPP), many still refer to it as the Nodal Point. Technically, the point at which you would rotate the camera/lens to avoid parallax is called the "entrance pupil".
The entrance pupil is a floating point located inside the lens, at the point where the light refracts or reverses itself before continuing to the image sensor or film plane. The entrance pupil is different on each lens and changes at different focal lengths.
Nikon
The entrance pupil (incorrectly referred to by some as nodal point) of a lens is the virtual image of the aperture formed by the lens elements in front of it, and is the place where light paths cross before being focused onto the CMOS, CCD or film plane. For a light ray to pass through the lens, it must be directed towards the entrance pupil, which is therefore the center of perspective. Note that the entrance pupil can be outside of the lens and even behind the film plane! When taking adjacent images you want to rotate the camera around a line that runs through (or very close to) the entrance pupil. By finding the entrance pupil of the lens, and rotating the camera about this point, you will assure parallax free images. Parallax is more obvious in the viewfinder with objects close to the camera. The more distant the objects, the lesser the parallax. If using a lens with zoom capability, the entrance pupil will change in position as the zoom changes. Because of so many variables, it is best to learn how to find the entrance pupil manually.

To locate the NNP of a lens, have the camera/lens setup on Nodal Ninja as shown below. You want the camera as far back on the upper rail as possible, pointing towards the horizon and parallel with the ground.

Nikon camera on Nodal Ninja 3
Position in front of the camera two objects - one nearer than the other. For example, indoors you could use two lamp poles, one at about 6 feet the others at about 10 feet, or if outside try using two fence posts or light poles. Any two objects creating a vertical line will work as long as one is positioned behind the other. In this example we'll use two floor lamps.
Looking inside the viewfinder, or at the LCD screen, rotate the camera so the two objects are towards the left side of the frame. Note the exact position of the two lamps. Ideally place the lamps so they aren't directly behind each - slightly offset them. Note the apparent distance between the two lamp poles, as shown below.

Finding the Entrance Pupil of a lens
Now rotate the camera so the two objects are now in the right side of the viewfinder frame. Go back and forth a few times, and watch to see if the distance between the two poles changes. If the distance changes, even slightly, then you have parallax and you'll need to move the camera and lens slightly forward (or back) on the upper rail.

Finding the Entrance Pupil of a lens
Loosen the camera mount knob and move the camera forward approx 1/2 inch (10 mm) and tighten. Repeat until the lamps remain relatively unchanged, as shown below. You do not want to any change in movement between the two objects.

Finding the Entrance Pupil of a lens
Finding the Entrance Pupil of a lens
Simple recap - outside you could use two trees or two power poles (target) - one forward the other distance and slightly offset from each other, giving you a space between them. When looking through the viewfinder of your camera move target from left to right side of viewfinder - if they move closer of farther apart, you need to adjust camera on upper rail either slightly back of forward until no movement is noted between the two while rotating camera left and right.

Note the position on both upper and lower rails and use the rail stops to set the position. If you change cameras or lenses, you'll need to repeat the above steps. Now you're ready to start shooting panoramas.

NN5 & NN5L Complete Manual


Chapter 1. Introduction + video tutorial
Chapter 2. Nodal Ninja 5 Features
Chapter 3. Nodal Ninja 5 Exploded View + video tutorial
Chapter 4. Hard Shelled Cases for Nodal Ninja 5
Chapter 5. Basic Assembly + video tutorial
Chapter 6. Removing and Replacing Detents + video tutorial
Chapter 7. Setting up with Known NNP
Chapter 8. Using the Camera Mounting Plate (NCP1)
Chapter 9. Mounting in landscape mode + video tutorial
Chapter 10. Quick Release Adapters
Chapter 11. Cameras / Grips with Off-axis Tripod Mounts
Chapter 12. About Parallax
Chapter 13. Finding the Entrance Pupil of a Lens
Chapter 14. Warranty
Chapter 15. Returns
Chapter 16. Copyright Information
Chapter 17. Contributors

Only buy from authorized resellers. If buying new from other than an authorized reseller, no warranties or product support are included.

topTop

Line

Nodal Ninja


Exclusive distributors of the Fanotec product line. Fanotec develops and manufactures exclusively products to meet the needs of the panoramic photographer. We offer products such as the award winning Nodal Ninja, the CNC machined Ultimate Line, Carbon Fiber Aerial Poles, Levelers, and many more related accessories. Many of these items may also be used for general photography as well.

Resellers


Check for a reseller in your country.
Resellers

News

Line
Line
NN3 MKII NN4 M1 R1 Poles EZ-Leveler II

Line
STORE    SITEMAP    FORUM
Testimonials | Trade In's | User Guides | Find a Reseller | Affiliates | Terms of Use | Your Account | Contact
Accredited Business Bureau   D-U-N-S Registered   LinkedIn   youtube   twitter   flickr   facebook   
Nodal Ninja®, 3454 N. San Marcos Pl. Ste 9, Chandler, Arizona, 85225 USA Customer Service ph: 480-659-9899 / fax: 480-452-0452 Hours: M-T-TH-F 8am-12pm
© 2013 Nodal Ninja® | Nodal Ninja® is a Registered Trademark - All Rights Reserved.

Verified Merchant   PayPal Verified